Search the community web
Full-text search inside the pages of Amiga forums, wikis, archives and personal homepages. The crawler reads them slowly, a few pages per site each week: where is the rest?
566 pages
-
Body
http://www.gvp-m.com/A2000combo030.html
Jumper settings for revision 3 G-Force030 accelerators Summary of jumper settings Jumper Default Description J2 SHORTED 68030 Enabled J3 OPEN MMU Enabled J7 OPEN RESERVED J8 OPEN…
-
Board Jumpers & Config - BlueSCSI Documentation
https://bluescsi.com/docs/Board-Jumpers-&-Config
…To increase brightness a lot, bridge solder jumper JP2 . Do not bridge both solder jumpers! This will cause LED damage! S1/S2 Configuration jumpers - Unused and superseded by…
-
SuperPLA V4 - IndividualComputers
https://wiki.icomp.de/wiki/SuperPLA_V4
…jumper settings Jumpers can be found at the bottom side of SuperPLA. Don't even try to set these jumpers without tweezers - they are really tiny and located…
-
ZuluSCSI - A hardware SCSI HDD & CD-ROM emulator
http://zuluscsi.com/ZuluSCSI-RP2040-Compact-Homebrew-Assembly/
About ZuluSCSI Where to Buy Resources ZuluSCSI Manual ZuluSCSI Firmware The correct, default jumper configuration for a newly-assembled ZuluSCSI Compact Homebrew should be: TERM_EN (Termination Enable…
-
Amiga Technical Resource - floppy drive conversion
http://amiga.serveftp.net/Floppy_drive_compatibility.html
…Panasonic JU-253-243P Unknown Unknown Sony MPF920-F No No Has one setting jumper. Sony MPF420-1 Yes N/A Has jumper grid for settings. To make…
-
Tutorial: Amiga Kickstart-Switch mit bis zu 8 Kickstarts (Teil 2)
https://mingos-commodoreblog.blogspot.com/2024/04/tutorial-amiga-kickstart-switch-mit-b...
…ROM-Umschalt Verzögerung Kein Jumper (default): 3 Sekunden Jumper A15-B3: 2 Sekunden Jumper B3-B4: 4 Sekunden Beeper Lautstärke Kein Jumper (default): Mittlere Lautstärke Jumper B5-B6…
-
Jumper/NVRAM Reference for the Amiga 3000...
http://amiga.serveftp.net/A3000_HardwareGuide/jumpers.html
Contents | Index | < Browse | Browse > Jumpers ~~~~~~~ The A3000D main board has many jumpers which configure the system. 16MHz PAL 25 MHz PAL 16 MHz NTSC 25 MHz NTSC 313311…
-
C64 reloaded - IndividualComputers
https://wiki.icomp.de/wiki/C64_reloaded
…SID voltage and filter selection Jumper settings for 8580 SID Jumper settings for 6581 SID For the HMOS versions of the SID chip, namely 8580 and 6582, jumpers…
-
Repair of a Trident VLB Graphics Card - LinuxJedi’s /dev/null
https://linuxjedi.co.uk/repair-of-a-trident-vlb-graphics-card/
…You can see some jumper pins are damaged. That isn’t the main problem, but something I will repair. Now, for the problem. Experts in VLB cards are…
-
How to use Keyrah V3 with BMC64 (and other Circle based projects) - Keyrah - Individual Computers Support
https://forum.icomp.de/index.php?thread%2F4525-how-to-use-keyrah-v3-with-bmc64-and-othe...
…stay tuned And now that i checked the code, i remember why there was no jumper setting - it doesn't work. The common jumper position (JMP_Detect, called…
-
Festplatten-Parameter, Jumper und BIOS Settings | Verein zum Erhalt klassischer Computer e.V.
https://www.classic-computing.de/festplatten-jumper-bios/
…IBM- und Kompatible Festplatten-Parameter, Jumper und BIOS Settings 1. September 2026 Georg Basse Kommentar hinterlassen Zahlreiche Einstellungen für Festplatten, Zusatzkarten und BIOS Einstellungen finden sich auf diesen…
-
OpenFlops Floppy Disk Drive Emulator – CBMretro
https://cbmretro.fi/product/openflops-floppy-disk-drive-emulator/
…OpenFlops board 3 x jumper Jumper setting for Amiga DF0: Jumper setting for Atari ST A: In ST floppy drive cable is reversed so OpenFlops is installed “upside…
-
Commodore Multimedia Breakout for C64 | időrégész.hu
https://idoregesz.hu/product/multimedia-breakout-commodore-c64/
…Color reduce – if short, a 300Ω smd resistor will reduce the color for the modern LED TV (default jumper option is OFF) Stereo/Double-Mono – stereo sound option…
-
Supradrive 500XP - World of Jani
https://blog.worldofjani.com/?cat=66
…Note jumper settings as seen on the picture above. TRM_ON , Target and PWR_ON . I used the bluescsi.ini settings from the Amiga section on the Compatibility…
-
Amiga Technical Resource - A3000 Technical Notes
http://amiga.serveftp.net/A3000_HardwareGuide/main.html
…With additions by Anthony Hoffman ----------------------------------------------------------------------------- Introduction - Overview of the A3000 Jumpers Jumpers / NVRAM - Settings and References Memory - Memory Expansion Boards - Expansion Boards Floppies - Floppy Drives SCSI - Hard Drives…
-
HD68 SCSI Adapter | Flamelily Retro
https://shop.flamelily.co.uk/hd68adapter
…The kit version will need both connectors soldering and the jumper pins. Tested and complete Female to Female adapter Includes a High Byte Terminator jumper Choose a kit…
-
V2.x Floppy adaptor – Ian Stedman's Website
https://www.ianstedman.co.uk/v2-x-floppy-adaptor/
…If you connect the SEL1 jumper and use the internal 34 way cable, every time drive 0 is connected, the jumpered drive 1 will spin up but not…
-
Build it Yourself - BlueSCSI Documentation
https://bluescsi.com/docs/Build-it-Yourself
…Install pins for jumpers. You should at minimum install and add jumpers to PWR_ON , Initiator/Target , and TRM_ON . A full list of all board level options…
-
H5 SIMM socket issues - exxos's Atari, Amiga & retro forum
https://www.exxosforum.co.uk/forum/viewtopic.php?t=8677
…Then out of desperation, i set the jumpers to 2Mb instead of 4mb and that solved everything, everything works, the GOTEK loads and everything runs. No matter what…
-
SX-32 Not working - I am TSB
https://tsb.space/bl0g/sx-32-not-working/
…Tested several jumper settings ( see jumper settings ) I did a wild guess, and replaced both CIA chips.. First attempt to boot with SX-32 was successful. And everything…
-
Amiga® Hardware Reference Manual: C Enhanced Chip Set
http://amigang.fr/rkm/Hardware_Manual_guide/node0099.html
…The A2000, when jumpered for one megabyte of chip memory, will function normally with the ECS chips installed, under both V1.3 and V2.0 Amiga System software…
-
Commodore 16 OpenCart
https://support.retrorewind.ca/en/blog/opencart64
…If you are using 64 KB (E)EPROMS, you can store up to 4 images, which you can select using the A14 and A15 jumpers above the LO…
-
Initiator Mode - BlueSCSI Documentation
https://bluescsi.com/docs/Initiator-Mode
…To use BlueSCSI as a Target again, the two jumpers must be moved back. Remove the standalone Initiator jumper and switch the other jumper back to the Target…
-
FRGCB - Finnish Retro Game Comparison Blog: FRGR #18: Ski Jump International trilogy (PD/Ville Könönen, 1994-2000)
http://frgcb.blogspot.com/2025/12/frgr-18-ski-jump-international-trilogy.html
…The way the scrolling works is, right after your ski jumper has hopped off of the ramp, the jumper graphic latches on to the middle of the screen…
-
Amiga CD32 SX-32 MK2 problem - I am TSB
https://tsb.space/bl0g/amiga-cd32-sx-32-mk2-problem/
…Change jumpers, for memory, no change. (see: jumper settings ) After the basic test, I was wondering if de edge connector is still in good condition. As we can…